Regenerative Braking in BLDC Motor Employing Buck Converter
MATLAB Model: https://zurl.co/WBmSM
https://zurl.co/m2zpT
#RegenerativeBraking #BLDCMotor #BuckConverter #ElectricVehicles #RenewableEnergy #EnergyEfficiency #CleanEnergy #PowerElectronics #Engineering

Regenerative braking in BLDC motor employing buck converter
Uses buck converter for regenerative braking in BLDC motor systems.
For Indian Customer: https://zurl.co/1eMpm
For International Customers other than India product-page/regenerative-braking-in-bldc-motor-employing-buck-converter
https://zurl.co/mYNm1
#RegenerativeBraking #BLDCMotor #BuckConverter #ElectricVehicles #EnergyEfficiency #GreenTech #SustainableTransport #MotorControl #EcoFriendly #TechInTransport

The BAPPR Keeps Your Addressable LED System Cool - We all love a nice strip or grid of addressable LEDs. It can add flair or an artis... - https://hackaday.com/2024/07/27/the-bappr-keeps-your-addressable-led-system-cool/ #switchingpowersupply #addressableleds #buckconverter #neopixels #hardware #ledhacks #ledstrip #rgb

Does anyone have a design for a 1-3A step-down DC/DC converter including EMI filter etc. using components available from LCSC that I could reuse or base my own design on? Even using a ready-made module (78xx replacement style) I'm going crazy with inductor selection for the input and output filters. As long as it's working well (especially EMC wise) and not too large I don't care much if it uses a ready-made module or individual parts.
#electronics #BuckConverter #EMC

Anyone out there used a buck converter to power a #pi5 from a power bank?

Getting that ideal 5V 5A combination seems impossible from unmodified power from portable sources. A DC-DC step down should be able to generate that V and A. But the voltage input has to be within a specified range to get the desired A.

Sure, the 5 can run off of lower amperage but not at all well. I'm looking to get the same performance as though I were using the official 27W power supply.

Also, WTH is up with the math? 5.1V and 5A does not equal 27W! I guess that 27W rating is the upper bound as the supply can also take in 9V 3A (27W). The supply must itself be using a buck converter. I just need one a LOT smaller. I'm aware of boards like this that may do the trick. https://a.co/d/dU6wNU3

Cheap Power Supplies with Fake Chips Might Not be That Bad - We all know the old maxim: if it’s too good to be true, it’s probably made with fa... - https://hackaday.com/2023/11/10/cheap-power-supplies-with-fake-chips-might-not-be-that-bad/ #buckconverter #counterfeit #lm2596 #ripple #parts #dc-dc #fake

I‘m currently trying out buck converters as a drop in replacement for linear voltage regulators. It should be much more efficient if they can handle the load. Let’s see. #synthdiy #synthesizer #psu #eurorack #buckconverter #kicad

Buck Converter Takes 8V to 100V - For those living before the invention of the transistor, the modern world must app... - https://hackaday.com/2023/09/17/buck-converter-has-tremendous-range/ #buckconverter #powersupply #converter #mp9486 #parts #dc-dc #buck #dc

Minimizing Stress on a Coin Cell Battery - When it comes to powering tiny devices for a long time, coin cell batteries are th... - https://hackaday.com/2023/08/10/minimizing-stress-on-a-coin-cell-battery/ #boostconverter #buckconverter #batteryhacks #switchmode #voltagesag #coincell #battery #dc-dc #life #smps

Op Amp Challenge: An Op-Amp Buck Regulator - Switching regulators have delivered such convenience and efficiency compared to th... - https://hackaday.com/2023/05/01/op-amp-challenge-an-op-amp-buck-regulator/ #opampchallenge #buckconverter #contests #hardware #op-amp #pwm

Didnt wanted to use the LM2596 so I looked for smth. more modern. These ICs are all synchronous buck converters with the same pinout and switching frequency. The VIN, VREF and current spec slightly differ for some of them. Pls refer to the datasheet.
I know there are better ICs out there but I was looking for something that has good availability which is important with the current supply chain situation.

It bucks. I think I got most of the bugs out of the PCB, and now with simple firmware that just does a constant PWM, it seems to work. Here it's stepping 12 volts from the battery down to about 2.5 folds for the light bulb. I didn't feel like getting the meter out, so you'll have to take my word for it.

My buck converter board finally came. I might start to get this thing assembled this week, at least in stages - I want to make sure the housekeeping supply works (the buck converter that powers the buck converter), then get the microcontroller on. Then get the rest of it together, and maybe move some power.

I should have enough parts to build two of these, assuming I didn't do something horrendous that requires a redesign. Like accidentally build an efficient radio transmitter.

So this board is about 2.5 inches by 5 inches, and will end up being four layers. That includes a main power/signal plane on top, a ground plane, a 5V plane, and an extra signal plane on the back. I haven't started routing it yet, and I may tweak the layout to space things out or make the board a little smaller.

Quick and (Not Very) Dirty Negative Voltage Supply - There comes a time in every hardware hacker’s career during which they first reali... - https://hackaday.com/2021/11/16/quick-and-not-very-dirty-negative-voltage-supply/ #boost-buckconverter #negativevoltage #boostconverter #buckconverter #powersupply #mischacks #inverter

Digital Cribbage Board Saves Scores, Marriage - When [ccooper] told his parents he was gonna start up his electronics habit again, the last thing he... - https://hackaday.com/2020/09/16/digital-cribbage-board-saves-scores-marriage/ #arduinonanoevery #cribbageboards #buckconverter #arduinohacks #rgbwmatrix #ledhacks #cribbage #games